A new day and a new thought! I choose LOVE!

I have several creative things posts that I have been meaning to get to, but lets face it I am a busy mom of 4 and that comes 1st!  Taking pictures, editing, writing - it all takes time that sometimes I just don't have.   I stated this blog for me to remember what I have done as I would often forget the details of how I did something when I went to try to repeat it years later.  If others find it and want to follow great - if I am the only reader I ever get - well that is great too!

I have not had much time for the physical creations that I love so much lately.  My focus has been more on the inner creation of myself.  I want to be the person that my Heavenly Father wants me to be and often I fall far short of that individual.  That is why I am so grateful for repentance and the ability to keep trying to do better.

I tend to have strong opinions and I am very hard headed.  Sometimes, I have forgotten that the person standing in front of me is more important than the idea that I am sure I am right about.  Which for the record I am right 99% of the time!  ;) As I have pondered all of this I have begun to think a lot about love and service.  Those are key to everything.  Me loving those around me through service will cause more softening towards the things that I know are right then all the heated debates in the world and even if they never come around to my way of thinking I am a better person for the service rendered.

I have been thinking a lot about this lately and then this morning my 8 year old came down the stairs wearing a cape.   Several years ago we had one of those panicked mornings where suddenly a child remembered that they were supposed to come to school dressed as a super hero or some such thing - I can't even remember the exact assignment or event, but I do remember that in literally 10 minutes I whipped up a cape.  I had a fabric on hand that was covered in hearts (this is when it pays to be a fabric hoarder!).  I then took another fabric that was covered in peace symbols and cut out a large L and put it in the center of the cape.  She was Love Girl!  Her super power was LOVE.

I had completely forgotten all of this until she came down the stairs this morning in that cape and the thought hit me so hard - LOVE IS A SUPERPOWER!  It is the greatest superpower one can posses and it can literally change the world and those around you.  What an amazing superpower to have and we all posses the ability to love.  We may need to work on loving some people in our lives more - you know the hard to love people around you - but we can all choose to love more fully and to not worry about the rest.  Christ turned the other cheek and loved those around him - even those who crucified him - how can we not look past the little slights and choose love instead of other emotions like hatred, jealously, envy, being offended, and selfishness.

I am going to try to love more fully through making myself more available to serve those around me. I am going to try to not be so hot headed and instead remember that more hearts will be changed through love then through me getting worked up about someone not seeing things the right way.  ;)  I am going to choose love!   I will definitely fail sometimes as I am only human and will never be perfect like Christ was while on this Earth, but that is where I will hope that this will spread and that those around me will also choose love and choose to move past my weak moments and instead remember my strong ones and remember that I am not all bad.  That is how you choose love!

I encourage everyone to CHOOSE LOVE!  That is the only way this messed up world is ever going to get any better.

UPDATE!  UPDATE!  Yah, I just finished this post like 2 minutes ago, but a thought hit me that I didn't want to lose.  SO, here it is.

Sometimes those around us who are the hardest to love are the ones who need it the most.  I think back to the times when I was the hardest to love and I know that what I needed more than anything was love and acceptance from those around me even though I maybe didn't deserve it or was shutting myself away for one reason or another.  Some of those times I was going through gut wrenching personal battles that almost no one knew about and I really needed love and understanding even when I may not have been the funnest person to be around.  So, the next time you encounter someone who snaps at you or is negative or is hard to be around maybe try to sprinkle a little extra love their way, because chances are they need it more than anyone else right then.  Thought done.  :)

UGGH! Anna Dress Glitter Problems

So, I finally got around to finishing the last details on the Anna dress!  Yay!  But that meant it was time to wash it once and see what happened.  The regular paint I used and then heat set with the iron stayed just fine and looks great!  The glitter paint that I used washed off.  :(  The glitter just made it look so good!  So, I had to find another solution.

Since I did not have time to go anywhere but Wal-Mart I had to use what they had in their craft department.  I found Tulip Glitter Dimensional Fabric Paint in the Diamond Color.  However, I did not want it dimensional - so I squirted some in a little paper cup and used a brush to brush it on and I think it worked!  Of course I won't be sure until I wash it, but that isn't happening for a couple of days.  One of the littles got invited to a last minute princess birthday party tomorrow and let's just say there will be a surprise guest and this dress will be perfect!!!!  Good thing we have Disney coming up and good thing I started with this dress!  I will have to post pictures after the big event happens tomorrow.

Anyways - back on subject.  I did have to paint it on without the stencil so there may be a few out of the lines glitter spots.  One of my questions about doing it this way is can this product be heat set with the other paint.  I know it doesn't have to be, but it would allow me to paint the glitter on while the stencil is still on.  If it shouldn't be heat set then I will have to always paint and hope I can stay in the lines after heat setting the other paint.  I am going to play around with it when I get a second so that I will know for next time.  In the mean time lets just hope this one doesn't wash off.  I am going on the assumption that since it is an actual fabric paint it won't, but stranger things have happened.

Princess Anna Dress is almost done!

Well, there are probably going to be a lot of sewing posts in the near future.  I have a list of projects a mile long and a good chunk of them involve sewing!

We have a pending Disney World trip coming up and my 2 little girls have requested various princess dresses to wear in the parks.  I am making 2 everyday princess dresses for each of them - assuming I don't run out of time!  The first up is an Anna dress for the soon to be 8 year old.

I am going to admit that the dress is not quite done, but I was so excited by how it turned out that I have to post it now!!!!  What is left

1. Hem the darker blue underskirt.
2. Heat press the stenciled parts to seal the paint to the fabric.
3. Cut a whole bunch of little strings and pull out a few around the waistline.
4. Wash it to get the white residue the freezer paper left behind off.  It didn't leave it everywhere, but you can see where it did.

But without further ado I give you the almost finished Anna Dress!

For this dress I worked off of two dress patterns and I did a bit of adapting as well.   Both patterns were purchased on Etsy.

Princess Party Dress

The Sugarplum Princess Dress

The part that scared me the most was the painting!  I had never done freezer paper stenciling before.  I bought a template here:Princess Anna Vest and Skirt Templates Only.  I converted this file into something my silhouette cameo could cut.  Made for a much better template!  Yay!  And I can cut them forever and to my hearts content!  Double Yay!

 As usual I can't get the pictures to go exactly where I want, but oh well.  On the close up of the bodice you can see some slight white residue.   See # 7 below or #4 above for an explanation as to what that is.











Things I would do differently and notes to remember:

1. Think of putting the glitter on before removing some of the stencils.  That's what happens when you realize you have some cool glitter paint after taking off the 1st round of stencils!
2. I would have done the stenciling after cutting out the pieces, but prior to sewing anything together.  I mean had this gone badly I would have had to start all over again!  If I had done it before doing any sewing I could have just cut out whatever piece I messed up on and it is flat so you can do the whole skirt at once instead of in sections like I had to.
3. Put cardboard or card stock or something under where you are painting and leave it until the paint has dried.  There is a good possibility the paint with seep through the fabric and onto whatever is beneath it.
4. I shirred the back and then sewed the bodice together.  Then I sewed that to the skirts after gathering them.  I am still debating if this was worth the reasons I did it that way.  It made the bodice more difficult to attach to the skirt as you had to stretch the back bodice out as you sewed them together, but if you do it after everything is assembled you have to manipulate the whole dress through the machine.  I think I will try assembling it first on the next dress.
5. Have a picture of the color scheme near me while painting.  I swear the leaves at the bottom of Anna's dress were all green, but apparently there is some purple down there as well.  Not critical, but makes it a little less authentic.  I think I like the way mine looks better though! 
6. I used the following products on this dress for the stenciling.  I had them all on hand except the fabric medium which I got at Michaels.

•  Acrylic craft paint
•  Martha Stewart Tintable Fabric Medium (there are other brands, but this is what I found at Michaels)
•  DecoArt Craft Twinkles in the Crystal color - see here for why not!
•  Freezer Paper
•  Various sponge brushes and paint brushes

7) I want to find a different template material.  The freezer paper worked o.k. for me, but it left a bit of itself behind in a few places which did not thrill me.  It is likely I was doing something wrong - not waiting until the paint was completely dry - maybe, but I have some other ideas and will likely try them the next time a project like this comes around.

I may add to this list as I think of other things, but those are the main ones I can think of right now.

Well, hopefully you enjoyed seeing this finished piece.  I love how it turned out and more importantly my almost 8 year old lit up when I had her try it on.  She is in love with it!

T's map room headboard!

Well, this is a long overdue post!  I started this project at the same time as J's headboard and then got so busy that I never finished it.  Then I finished it a few weeks ago right before we left on a big vacation.  So, this post has been a long time coming.

T's Headboard!!!!!!!

And a close up of some of those printed buttons!

Here is what I learned from this project:

1) When printing on fabric add ink!  The fabric sucks in ink more than paper, so you want to make sure what you are printed is a bit over saturated so that it will look right on the fabric.  

2) I also learned that maybe a blackout curtain is not the best material to use for a tufted headboard.  I wanted to use the same fabric as his curtain and since the curtains were only $10 a panel it seemed like a good idea at the time.  The problem was that the blackout coating they put on the back of the fabric caused the fabric to not have any give.  This lead to a less smooth look in the finished product.  Not awful, but not as tight and smooth as I would have liked.  You can see that it looks more wrinkly than the one I did for J's room and now you know why.  I still like it, but it does bug me a bit that it is not tight and wrinkle free.

3) Double check the size of the staple you need.  I put the wrong size in and they stick through the back of the board.  Not a huge problem if it is hanging on the wall, but let's just say that I ended up with a few scratches as I was working on the headboard.  A shorter staple would have prevented battle wounds! 

That is all for now.  One of these days soon I have to redo the artwork on his wall.  I bought a few new things and I need to rearrange what is there.  I also was inspired today by a post I saw somewhere to start looking for one of the old pull down maps that they hang in classrooms to put in his room.  I found a couple online, but want to see if I have too much already and I need to wait for the cost to fit into the budget.  But isn't that a cool idea!  

Printing on Fabric for T's headboard

Well, let's just say that the end of the school year and the first month of summer kind of did me in.  Way over scheduled!  I hate it when that happens, but with 4 kids it is something that occurs often.  This week things have slowed down a bit and next week I am calling a no schedule pool week to make up for the first month of summer being so busy.  Anyways that is why I have not written any posts or done many projects!  Time to remedy that by finishing T's headboard that I started a few months ago.

So, here is a quick tutorial for printing on fabric!  The button fabric was printed using this method!

Besides your inkjet printer and some fabric you will need the following:
(not pictured is the Bubble Jet Rinse)
The freezer paper can be found at the grocery store near the tin foil sometimes.  It will be a different brand as the one I have is specifically for crafts and comes in sheets instead of rolls.

You first follow the directions on the Bubble Jet to treat your fabric.  It is pretty easy.  Cut a piece of fabric slightly larger than you want and soak it in the solution for about 5 minutes and then hang it to dry.

Once it is dry you then iron the shiny side of your freezer paper to the wrong side of your fabric. I forgot to take a picture, but I had a scrap that will hopefully help you see what I mean.   the top part that I am peeling up is the fabric and the bottom is the freezer paper that I have ironed it onto.

Then cut the fabric/ freezer paper down to the size of paper your printer will take - typically 8.5 inches by 11 inches.  for my printer you place the side you want printed on down, but you will have to check your printer to see.  You want to print on the side of the fabric that the freezer paper is not attached to.

Then use the proper settings for your printer to print your image onto the fabric.  You may have to play with your printer and the fabric a bit to find the right settings.

Once you have it printed let it dry for awhile and then peel the freezer paper off of the back.  You are now ready to make your buttons!

This project hit a snag when my first try print of maps on fabric for his buttons didn't work.  I forgot that fabric will suck in the ink more than paper and turned down the amount of ink being printed.  I had to fix that problem before I could move on.  They turned out perfect on the second try.  This time I turned up the saturation on my file that I was working with so that it almost looked a bit overdone which caused it to look perfect on the fabric.   Just remember that when you are doing the printing.

I then used the directions from this post to make the actual buttons:

https://www.blogger.com/blogger.g?blogID=8033456016525440553#editor/target=post;postID=4920586827072482513;onPublishedMenu=allposts;onClosedMenu=allposts;postNum=2;src=postname

And you end up with this!

Well, that is a super quick version of how I did the buttons for T's headboard.  This week or maybe next I will be putting the whole thing together and getting it hung on his wall along with a few other fun things I got on my girl's week for his room.  Yup, even on the girl's week us mom's still think about our kids!  I am pretty excited to put the finishing touches on his map room!

Headdboards Galore!: Post 4: J's are done and hung!

Ta Da!  Here it is!  And I love it!!!!

I would definitely classify this project as a learning experience!  I am glad I did so many buttons on this project as I was able to adjust how I was doing it and make it easier for myself for next time.  I think if it hadn't had to put around 130 buttons on the 2 headboards I would have done it exactly like I read and forgotten how time consuming and frustrating it was before doing this project again.

I am going to tell you how I did it, but I am new to this tutorial thing - so if something isn't clear you can ask and I will try to explain better or you can search for other tufted headboard tutorials out there in internet land.  There are a few.




When we last left off we had this:

The next step is pretty simple.  Use your fingers to make holes in the batting everywhere that there is a hole in the foam. Just kind of tuck the batting down into the hole in the foam as you make the holes.

 I actually added a step that most people won't need.  I used 19-20 different purple fabrics for the buttons on this headboard.  I wanted to make sure no two that were the same were near each other.  So, before I poked holes in the batting I laid all the buttons out to make sure I knew where I wanted them.  Then I transferred them to my ottoman in the same order so I would know where they went.  I also threatened the lives of all of my children if they got anywhere near the buttons and messed them up.  ;)  Since most people use the same fabric on their buttons or will go for the random I don't care look - you can probably skip this step.

All the tutorials said to lay your fabric out and to center it on the headboard and then to start from the middle and work your way out.  I had 8 yards of fabric and was hoping to have some left over to cover her box spring.   I did not want to waste any fabric.  So, I of course ignored those directions.  I did not cut the 8 yards of fabric and laid it out over my headboard with the cut end overlapping one end enough so that I could staple it under when done.  You can either center your width on the board or I also left one side longer than the other and just made sure I would have plenty to staple under on the shorter side.  Then I started at the end with the cut end of fabric overlapping it and did one column from top to bottom at a time.  This seemed to work just fine for me, but you will have to decide what will work for you.  No promises here.  Once I got to the end I cut the excess and did the next board the same way.   These pictures are not spectacular, but I was trying to show you what I did.  I did not get very good pictures of this.  The top left picture was taken from the end of the board.  So the bottom of the picture is actually the end side of the long headboard.   The bottom left picture is looking at the shorter scalloped headboard from the bottom of it.  You will understand the comments on the pictures after you read the whole post.

All the tutorials I read said that applying the buttons and doing the tufting was much easier with 2 people and boy were they right!  I started out having my oldest 2 help me, but their attention span was not 130 buttons long and they were at school for big chunks of the time that I wanted to work on it!  I could still do it, but it was a lot harder, took more time, and I was not getting the buttons as tight as I wanted.  So, a new plan needed to be formed!

Let's start at how I started doing it:

Thread the thread through the hole from the bottom.  Thread it through the button and then back down thorough the hole.  Pull on the thread from the bottom while pushing the button down and helping the pleats to be where you want them.  Then have a child laborer, aka my oldest son or daughter,  push down on button and board while you continue to pull on string and climb under the headboard.  Take staple gun and begin to staple thread 3 times on back of board, all while child laborer is hopefully pushing down hard enough so that the board does not push up causing the staple to not go in tightly.   Repeat 130 times!  You can see where this was quite the process!

Once you get to this point this is what you do on the back (This applies no matter which of the ways you choose to attach your buttons and make your tufts):

I was putting 3 staples over each string.  Make sure your button is as tight as you want it before you put the staples in and then staple.  You want to move the string to different angles for the different staples so that it is less likely to slip and you want to make sure your staples are tight.  It is easier to get them tight if you staple with the board face down on the floor, but that can make it harder to make sure your button is where you want it.  You will have to play with it and see what works best for you.

Then a small miracle happened.  One of those blessings that at the moment it happens you do not see as a blessing, but later you are so glad it happened!  My trusty staple gun broke.  For a single moment I considered running to the store and grabbing a new one just like the old one and then I realized how sore my hands were from the old one and made a decision.  It was time to upgrade to an air powered staple gun.  I did my research and the one I wanted was not available at the local store - so I ordered it online.  Luckily I have free 2 day shipping on the site I ordered it from!  The new staple gun opened up the possibility of a whole new process!  YAY!!!

New way:

Press fabric into hole where button goes with fingers.  Get everything laying just like I want it to and as tight as you want it and then put nose of staple gun into hole and move your fingers out of the hole. Insert a staple to hold it there.  Repeat 130 times or however many buttons you have.  The new staple gun was not flat on the end like the old one, but had a nose that fit oh so nicely into the hole!  Once all the places where a button will go are stapled down you start threading your needle and button through just like you did before, but I was able to do a whole bunch at once without securing them with the staples on the back and then flip the whole board over onto the floor and pull the strings tight and staple them down.  Because the fabric was already secured I did not have to worry about getting the pleats right and the buttons/ strings didn't pull out as they would have if the fabric were not already secured to the board below the button.  Because I could easily flip it over onto the floor the board didn't move and I could get the staples tighter.  And then there is the fact that the new air powered staple gun was so easy to use and my hands were not killing me like they were from the manual staple gun!  Win!  Win!  Win!!!!!!  One person doable and so much easier!  And if something did not line up right it was so much easier to pull a staple out than it was to cut the string and remove the button.  At least I thought it was easier.
 

I forgot to take pictures of adding the buttons after this, but you just repeat the steps from above for that, but everything should be in place - so you don't have to worry about getting your pleats right or anything.  Just apply button!  Here are the pictures from above again to remind you.

 

I  also discovered one way not to do it.  It might work for you, but after an incident I decided it was not worth the saved time to chance a later disaster.  I threaded the button on the string first and then threaded both ends of the string through the needle.  I then used the needle to thread the string through the fabric and hole from the top.  And then I pulled it tight and stapled it in place just like the other two ways.  The problem - this puts a lot of extra pressure on the shank of the button and I had one that later popped off the wires that hold the string.  Since the two sides of the string go though 1 hole in the fabric it is only the button holding everything in place.  I fixed it the lazy way as I did not want to recover another button.  I put a new string though the hole to hold it - without a button on it and then I glued the button over the top of the string.  Let's hope the others that I did that way don't do the same thing over time!  Or I will probably try the other not great, but will work method of fixing it.  Staple the fabric back where it should be and then glue the button on top.  I considered this as a 4th method, but was afraid the staples would pull out too easily.   Maybe your buttons won't break as I only had one do that, but I don't think I will chance it again!

One other thing: I also wrapped the edges and stapled them as I went.  I waited until I got a few rows past a spot and then would pleat it and wrap it.  I found that most of the time pleating it at the center of the button to the edge worked best for me on the rectangular sections of headboard, but this is something that you will have to work with and see where the pleats seem to want to go naturally or where you can force them to go because that is where you want them.  ;)  You could also wait and do all the edges once after all the button tufting is done.  That is probably the way most people would do it anyways.  I just like to do things my own way!

Once you finish applying all the buttons and wrap the edges you turn the board over and trim off all the excess fabric and batting.  You are done!  Well, you could try to cover the back, but who will ever see it!  And you need to apply something to hang it on the wall.  But, the hard part is done!  Here is my finished product!  I love how it turned out!  The straight purple is her sheets.  I think I kind of prefer it with just purple, but I am not replacing her bedspread right now and she is 12 and loves it.  I think 12 year olds like things busier than adults do - or at least mine does!

Cost analysis:

I think each headboard was right around $100.   So, $200 for the two in J's room.  That is if you don't count the tools I bought to make them.  If you count those then you are probably closer to $130-$140 each.  Not too bad!  The cheaper ones on Etsy seemed to run around $300-$500 each with an additional shipping fee of about $150.  So, way cheaper than the custom ones I found there!  Another win!

Now on to my son's headboard.  That one may be a few weeks off.  I still have to figure out the whole printing on fabric for his buttons and the next few weeks are a bit crazy!  Stay tuned for more!

Headboards Galore!: Part 3: Buttons! Buttons! and more Buttons!

Progress!  Still not done, but so far so good!

For the last few weeks I have been working on buttons.  J's headboards are going to have around 130 buttons and T's headboard is going to have 24.  I am making the buttons - so that is a whole lot of work.  The good news is that J's are now done.  T's involve an extra step that has encountered some temporary technical difficulties!

Let's start with J's buttons.  They are pretty easy.  You buy a kit that has a tool in it and as many refill kits as you need.  I purchased mine online this time as I needed a whole lot, but I have purchased them at the local fabric store before.  Here is a picture of everything you will need. 

 There is a template on the back of the box of button pieces that tells you how big to cut the fabric.  I purchased templates for different sized buttons that are a bit more sturdy than the cardboard one on the back of the box.  So, yours will likely look a little different, but will accomplish the same thing.  You trace it on your fabric and then cut it out.

After cutting it out you place your fabric on the bigger of the 2 tool pieces with the hollow side up and the ugly side of the fabric up.   Then place the front button piece face down on the fabric.  Use your fingers to push the button piece and the fabric down into the hollow center of the tool.

Fold all the edges to the center and then place the shank of the button on top.

























Place the smaller tool piece on top of the shank with the open side down and press.  You may hear a click and you want to make sure you get all the edges of the shank into the top part of the top button piece.

And here is your finished product!  Now repeat for as many buttons as you need!

 And I wasn't even done here!  ;)









So now on to the minor and temporary technical difficulty with T's buttons.  T has a map room.  He loves that kind of stuff.  I bought an extra black curtain and am going to use that as the fabric for his headboard.  It was $10 and matches his curtains.  Double win!  Any how,  I want his buttons to be maps.  So, I am attempting to print on fabric.  I read up on it and got to work.  But the first attempt had some problems:

The fabric peeled off of the freezer paper backing in the leading corner causing the black ink mess and I need to darken the images so they don't look so washed out when the ink soaks into the fabric.  So, I will try again, but maybe not until I finish J's headboards.  I will update you when I do!

The next step, the actual tufting, is the most time consuming - especially when you have 130 buttons to tuft and my staple gun broke part way through the 1st headboard.  On the bright side I am replacing it with an automatic one that attaches to our air compressor.  My hands are so thankful it broke!  ;)  So, expect a few days to a week before I post the finished photos in my next post!  

Headboards Galore: Part 2: Cool tools!

When we last left this project this is what we had:

Remember how I so carefully drilled all those holes?  Well they are still there they are just convered up with all that foam!  So, now we get to transfer the holes to the foam.   Take a long needle and stick it through the hole from the back until it pokes through the foam on the front.  I then took a Sharpie and held it for a second on the foam, against the needle, kind of down into the hole.  I forgot to take a picture of this part, but you are basically marking the spot that the needle came through.  A couple of tips - try to get the needle straight through the foam and not at an angle or the next step will not end well as your two holes may not match up.  Repeat until all the holes are marked on the foam.

 Now comes a fun part.  You have to make holes in the foam.  My buttons were 7/8 inch in size and so I decided to go with a 1.5 inch hole.  You can accomplish this several ways.  You can cut through the foam with very sharp scissors, a box cutter might work but I have not tried that, or you can do it the slightly more expensive but save yourself a lot of headache way like I did.  I bought a button tufting foam cutter.  They come in a radius of 1 in., 1.25 in. or      1.5 in. that I saw.  There could be other sizes as well.  You hook that little tool up to a drill, spray the end of it with silicon spray often, center it over a dot and drill away!  Nice holes that are uniform in size and fairly easy to cut.









It is kind of hard to see, but this is what you end up with - this was the first try so there is only 1 hole and one plug sitting on the foam.

My husband did this part for me why I was marking the other headboard.  He tried doing it while it was propped against a wall, but ultimately found it was easier to do if you laid it flat on the ground and then started drilling.  He also highly recommends spraying the foam cutter with the silicon spray often as that made a huge difference!

The next step is to add a layer of batting over the foam.  All the tutorials I read did this - I don't know why, but my best guess is that it kind of smooths everything out.   I happened to have some in my supply closet that covered both of J's headboards, but I am going to have to make a run to get more to cover T's.  You staple it to the back with a staple gun and then trim off any excess.

And this is what it should look like at this point.  Notice the detail on the top is not as obvious.  When I get the fabric on and start pulling things tight that should bring out the detail in the top again.

So far, so good.  Stay tuned for the next post on this project.  It is looking more and more like it is actually going to work!  YAY!!!!!!

Headboards galore! Part 1: Wood and Foam!

So, when I try something new I tend to jump right in.  No, starting small until I figure out if it is going to work or not.  That is just how I am.  This weeks project has been on my mind for months and months......  Headboards.    On my to do list has been a deeply tufted headboard for my oldest daughter (actually 2 - her bed is in a corner and so we are doing one for the head of her bed and one for along the side of the bed that is against the wall) and a not quite as deeply tufted headboard for my son.  This week I finally got to work on them.

I read all sorts of tutorials and then jumped right in.   After reading all the descriptions I decided that I wanted a deeply tufted diamond tufting on my daughter's 2 headboards and less tufted rectangle tufting on my son's headboard.  First I measured and used graph paper to lay out the size and tufting pattern for each headboard.

Next, I grabbed the hubby and we headed to Home Depot.  We grabbed two 4 ft x 8 ft pieces of wood.  Cost was around $45.  I originally thought I would need 3 sheets, but adjusted the height of two of my headboards to 24 inches so that I could get 2 out of 1 board and save some dollars.  Wood is not cheap!  We had Home Depot cut the boards to size for us.  The headboard that is going at the head of my daughter's bed was going to have some detail and not be just square.  So, I worked with my daughter to create a shape we both liked and then made a template.  I sketched it unto the board and borrowed a friend's jigsaw to cut it out.  I love how it turned out!

Then, I transferred the grid lines from my graph paper to the wood and marked each place that I needed to drill a hole with an X.    This, is where I surprised my husband.  While he was at work I found his drill, figured out how to switch the bit, and drilled through each X all on my own.  He acted surprised when he got home - so apparently he didn't think I knew how.  ;) 

 The next part involves foam.  I used an egg crate type foam mattress topper from Walmart.  I think it was cheaper doing it this way then buying the foam padding from the fabric store.  That stuff is expensive!  I used a total of 3 full size foam mattress pads.   I bought these a while back and I am going to have to swing by Walmart to see how much I paid.  I will update this when I find out.  I also used a can of spray adhesive.  The one pictured worked OK for this project, but I might try a different one next time.  I just already had this one on hand.  I had to piece the foam together in paces - which is totally fine!  I also doubled it up so that I had 2 layers over my whole board.  I wanted it to be a little thicker and I had enough foam to do it.  Yay!

After all the foam was adhered to the board or another piece of foam with the spray adhesive, I flipped the board over and used scissors to cut along the edge.  I was going to use a box cutter, but couldn't find it and found that my sharp sewing scissors worked pretty well for this.  They did end up with adhesive residue on them that I am hoping I can get off - so beware if you use expensive sewing scissors!

 And that brings us to where I am now.  The boards are covered with the first layer.  The next steps are to get all of my buttons made and covered (130 for my daughter's and 24 for my son's).  And to cut out parts of the foam on my daughter's so that the tufting gets good and deep.  More on that on my next post!

I have never done this before and what you see above is where I stopped about an hour ago when I wore out.  I hope to get this project completely done in the next week or two.  I will post updates - so you will know if it is total fail!  Wish me luck!  I am going to need it!